Everything You Need To Fix Your Jacuzzi Hot Tub
   
 
Requires a Java Enabled Browser.

PC Boards, Chips, and Transformer
 

Topside ERROR CODES Click Here
 
Note:
Boards that look alike but have different chip #'s and are not interchangeable.
Older boards with XXXX-0XX are NOW XXXX-2XX. Example: Old: 6600-088, NEW 6600-288.
6600-092
6600-161 LCD J-400 2008+ (replaces 6600-098) $825.00 msrp $577.50

6600-092
LCD Circuit Board Chip # 9.50B
 $825.00 msrp $577.50

6600-101
LCD Circuit  Board Chip # 9.70B

3 Pump J-380, J-385

 $825.00 msrp $577.50

6600-288  
6600-288
Replaces:
6600-088
LED Circuit Board $432.00 msrp $302.40

6600-286  
6600-286
Replaces:
6600-086
LED Circuit Board J310/315/325 $381.00 msrp $266.70

6600-288  
6600-287
Replaces:
6600-087
Circuit Board J-230 $432.00 msrp $302.40

6600-286  
6600-289
Replaces:
6600-089
LED Circuit Board J-210/220 and Del Sol $381.00 msrp $266.70

   
 
LED or LCD?  What's the difference.
Basically, if your topside control has little light legs that glow you have a LED. Some models have a LCD topside which means the legs are crystals and must have a backlight be seen at night.

 

EPROM Chips ONLY for above PCBoards
 

Example 6660-275
Chip # Our # Board Chip is Mounted On Our Price  
6660-328 Rev 9.51A 02-328 6600-098 $31.50

6660-268  Rev 9.51B 02-268 6600-161 $33.00

6660-279 Rev 9.50B 02-279 6600-092 $31.50

6660-282 Rev 9.70B 02-282 6600-101 $31.50

6660-275 Rev 3.53 02-275 6600-286/288 2002-3 J300 Series Uses 2hr Filter Cycle $35.88

6660-277 Rev 3.56 02-277 6600-286/288 2004+ J300 Series Uses 1/2hr Filter Cycle $35.88

6660-276 Rev 5.54 02-276 6600-287/288/289 J200 and DelSol Series $35.88

6660-284 Rev 5.56 02-284 6600-287/288/289 2006+ J 200 Series $34.50

 
 

PC Board Transformer
  Desc Part # MSRP Our Price  
2002+
Picture Shown NOT actual picture of part. Part does NOT include plug. Must reuse plugs from old transformer. New transformer comes WITHOUT plugs.

6560-274

$60.00 msrp

$42.00


 
 
Part Education
To Make You a Spa Brain

Spa PC Boards: Jacuzzi printed circuit boards are similar to your pc computer board. The chip is programmed to operate a certain way and turns components on/off at certain times and for certain reasons.

Over the years many have asked why a board will fail. Sometimes the failure might be caused simply over time such as internal components failing and some even causing damage to other components. So boards look perfectly good yet will not operate or at least, correctly. Some simply have components on board that fail making the board not operate. Brownouts, blackouts, voltage surges and spikes can cause damage to your spa's board.

Over the years some have tried to change only the "chip" on the board to see if that solves the problem. The success has been limited but if the board looks perfectly fine, it could be the solution. More often you are simply trying to fix the problem in the wrong way.

Most if not all boards have settings. Easiest way to configure a new board to work is match such things a "jumpers" from the only to new. If you look at the boards you will see the jumpers.

FYI: It always makes sense to "ground" your body by touching something metal that is properly grounded. This will avoid any chance of a static charge damage to the new board.

 

 

 

 

 

 

Copyright © 2008-10 Clear Creek Spa Service - B Bouman and Company LLC
Jacuzzi® is a registered trademark of Jacuzzi Inc. -  Jacuzzi Premium  and Jacuzzi Hot Tub are registered trademarks.
All Rights Reserved